Sleeping On It…

img_8207

Partially quilted light areas

Never ceases to amaze me how my brain keeps working while I sleep and when I wake I have a solution to the problem I walked away from (temporarily). I trust my sleeping brain implicitly – it always comes through; there’s always a solution the next day. That was how I worked when I was writing – stop when I got to a place where I wasn’t sure how to proceed – next day, ideas were just there! Always! Same with the quilting – walk away from a decision point, come back next day and there’s a way to work things out.

Last night the problem I needed to solve was how to quilt the light diagonal spaces in the quilt because the fabric expanse was too big (4″ x 20″) to lay flat – I needed to fill the space with something. I thought about just straight line quilting but that seemed too boring. I woke this morning thinking about stippling and knew how to set that up. I traced the light diagonal shape onto paper, sketched in some stippling, scanned the drawing, opened the image in Photoshop and scaled it to the right size, saved the image, imported it as background into my TruEmbroidery Create software and created a design based on my sketch (had to do some adjusting to balance the fill). I did a test run to see  how the stippling worked out – it was perfect! Just the right size for the space.

So far, I’ve quilted in eight of the spaces – I have four large ones, four light triangles and eight smaller diagonal pieces to go – that’s three different embroideries, in all, to fill all the different shaped light areas. I’ll probably work at this some more this afternoon, and it will still take at least another day, if not two, to complete the fill work.

Cost of table topper?

Overhead: $0 – I won’t cost the electricity to run the machines, the iron, the lighting in the studio, rent for the studio space.

Supplies: $100 – the backing fabric alone cost me $40 (cotton fabric these days is ~ $20/m) – then there’s the four half metres of red/green printed fabrics, plus the metre of dotted cream fabric – so $100 is an estimate, my materials may have cost a bit more and I’m not counting in thread or machine needles.

Batting: $30 – batting is $26/m plus tax – the cotton needle punched batting I buy is 90″ wide so I needed a metre.

Labour: $20/hr – I’m a skilled artisan, my time is worth more than minimum wage! My education consulting hourly rate used to be anywhere from $100 – $200/hr, my web design hourly rate is $50/hr. I should be charging the same kind of rate for the sewing/quilting but let’s go with $20.

I will have put in at least 15 hours (probably more over 7-8 days) to make this Christmas table topper so labour = $300.

Total cost for the topper were I selling it: $430.

However, the topper is a gift for a long-time friend; it’s a labour of love.

Advertisements

Christmas Table Topper

img_8206

Table Topper

I’ve worked on this project all day – started quite early piecing all the small blocks together. Then I discovered I hadn’t bought enough backing fabric so I had to go out (just as the storm was starting) to pick up 2.1 m of backing fabric to be able to cover the length (81″) in one piece.

I’ve done about half of the stitching in the ditch. I got bored, so I set up an embroidery design to quilt the eight small squares and the “diamonds” in the centre. That’s now done. I’ve stitched around the outer edge 2″ from the edge to establish a border. I chose not to bind the project, instead, again I did a pillow case finish with the back.

Because the edges of all the blocks are cut on the bias, I’m having trouble getting every section of the topper to lay flat – it’s most obvious in the light diagonal sections – the way to solve that, of course, is to embroider/quilt each section and I may actually do that tomorrow. It isn’t quite as simple as it sounds because each of the long light diagonals is 17″ – I don’t have a hoop large enough to do that. so each of those sections would have to be done as two embroideries. Hooping each of those areas, however, would stretch the fabric flat and the stitching would hold the fullness in place so the topper would look flatter. I’m going to sleep on it!

Finished dimensions: 35″ x 81″ (to fit a 34″ x 80″ table with both extensions open).

Christmas Table Runner

Christmas Table Runner

Christmas Table Runner

I used the leftover fabric from the table topper to make this runner for another friend. It should look nice on her dining room table. It’s constructed on the diagonal – that’s how it’s possible to have the central “diamonds” overlap the triangles on the sides (with the addition of a narrow strip attached to the light strips to create the illusion of  overlap).

Took a bit of fiddling to piece the top and I made some mistakes that I took apart and redid – which is why the two mid-side triangles are a different fabric! (They were meant to be the same as the other red/green fabric). In the end, however it all worked out with the fabric I had on hand.

I chose not to bind the runner, instead attached the back using a “pillow case turn” – I just didn’t have enough of any one of the prints to do a complete binding and the point was to complete the runner without having to buy more fabric and, besides, I like the neatness of the finished edge – nothing to distract from the basic elements.

img_4152

Blocks stacked, ready to chain stitch

Now back to the table topper – the pieces are all lined up on my sewing table ready to be chain stitched and the top assembled. It’ll take a couple of hours and it will be done, too.

Christmas Table Topper

img_6885

Christmas Table Topper – in progress

Zippered bags finished, I’m back at work on a Christmas Table Topper for a friend. Her table is 34″ x 80″ extended – with my half-square triangles finished size = 5 3/4″ I’ll finish at 35″ x 80 1.2″ which will work on her table.

So back to half-square triangles – in this instance I have four strong printed fabrics with a light background. I wanted to try a truncated “Starburst” but the layout looked like nothing with my finished dimensions so I’ve opted for “flowers” with two different square print centres which will alternate from section to section. The square print fabrics are tying the coloured triangles together and providing some continuity to the design.

This is one end of the topper – there are two more sections of three rows each and a final end section of four rows for a total of 14 rows. I have backing fabric which I’m not going to bother to piece and I’m not planning on using batting but plan, instead, to use a panel of muslin to give the topper a bit of heft but no puffiness – balancing wine glasses on a quilt topper can be problematic. The muslin should provide just a small bit of substance to the topper. I plan on stitching all three layers using “stitch in the ditch” – but you never know, I might do something more complex once I get the topper assembled.

I’m also planning to use a pillow case assembly for the back – no binding, the back is placed on the top, right sides together; you sew around the outside (1/4″ – 1/2″ seam allowance) leaving an opening on one side so you can turn the whole thing inside out like a pillow case, press, hand stitch the opening closed, then quilt – the fastest way of completing a quilt.

No time tomorrow to work on this but I will likely be able to get the top pieced on Thursday. Finishing the topper will take no time at all. I’m not in a rush – don’t need to give it away until Christmas Eve.

Then a table runner using the same fabrics but NOT half-square triangles! I want something with more density for the runner.

So the Christmas sewing, which I never intended doing, is moving right along.